iei 212w weatherproof keypad programming

#IEI 212W WEATHERPROOF KEYPAD PROGRAMMING CODE#

There are three LED's to indicate operation status and provide the user with visual PIN entry confirmation. Here is the IEI manufacturer's descriptionĪffordable single door access control keypad designed to meet the indoor or outdoor flush mount needs of lighter volume access control environments. Does not include plug in wiring harness or mounting screws. Press * to clear (yellow LED should start flashing) and start over from step 2 or 3 above.IEI 212i replacement keypad only. If the yellow LED lights solid while in programming mode, an error has occurred.

#IEI 212W WEATHERPROOF KEYPAD PROGRAMMING CODE#

If you forgot the master code or it is not working, momentarily push SW1, (see wiring diagram for location) to enter programming mode and go to option #19 on the Programming Options chart to default keypad.Codes may be from 1-6 digits in length, and digits may be repeated.By default (auto-entry is off), all codes must be followed by the * key.The master code allows access to programming mode and activates the main relay.1The master code is always stored in user location 1.Door♦Gard Command and Control keypads are factory programmed with a master code of 1234.If you must change the default settings or additional functions are desired, please refer to the Programming Options Chart after you are familiar with the Programming section. The following default settings are factory programmed: Programmed information is stored in non-volatile memory so it won’t be lost if power is removed.ĭoor♦Gard Command and Control keypads are designed for easy installation in a minimum amount of time. You can program your keypad in your shop or at the installation site. Refer to programming section to program your keypad. Enter the master code (default = 1234) followed by the * key and the relay energizes. If you do not get the continuous light, the memory has been corrupted and should be re-programmed with the default command (see option #19).ĥ. Note: Self-test mode can be used to troubleshoot a keypad in the field. The yellow LED flashes 3 times, then turns on solid for 3 seconds If all 12 keypresses are verified, the keypad enters self-test mode. Connect the negative (-) lead of your power supply to the terminal strip (TS1) V- input.Ĥ. Connect the positive (+) lead of your power supply to the terminal strip (TS1) V+ input.Ģ.

*Voltage Outputs may be converted to 1 Amp, Form- C relays by adding the 293 Auxiliary Relay Board (Model # 0219000).ġ. This output is not available on all models. The 250 comes with a power supply and a printer cable and it easily connects to any parallel printer.

Up to 8 keypads can be monitored simultaneously. Using the 250 Printer Interface (not included), you can get an accurate real-time audit trail. Please remember to access program mode when auto entry is on, do not press the * key (Press: 99 # master code), however the * is required while entering programming commands. To use this feature, the user codes must be the same length as the master code. You only need to enter your code number (without pressing *) and the relay activates. This feature is used when you don’t want to press the * key after entering your code. This output is not available if you are using the IEI 250 Printer Interface. You can use this to turn on lights, CCTV camera, or notify a guard. You can turn this off through programming.ĭoor♦Gard Command and Control keypads can be programmed to energize a voltage output whenever a key is touched. The auxiliary outputs activate for their programmed time.ĭoor♦Gard Command and Control keypads, by default, acknowledge a keypress by momentarily illuminating the yellow LED or activate the sounder.

You can also program the REX to operate any combination of the available outputs. By default, it operates output 4 and activates for 1 second.īy default, upon a momentary closure this normally open loop triggers the main relay for the same time period as the Master Code. Panic is activated by pressing the * and # keys at the same time.

Some models have 1 Amp form C relays and other models have negative voltage outputs with a 50mA sink.* They can be controlled individually or in combination by a code. You can program these outputs as timed outputs (1 to 90 seconds) or to toggle (latch). See the Wiring Diagram and Specifications for the relay electrical specifications. The main relay is a form C relay, which you can program as a timed output (1 to 90 seconds) or to toggle (latch). The Master Code is always stored in user location one (1). Codes can be 1 to 6 digits in length and digits may be repeated. The Door♦Gard Command and Control keypads allow up to 120 individual user codes. It takes seconds for an authorized user to change codes. LED or sounder guidance makes programming easy. Non-volatile EEPROM memory means your codes and instructions will be there whether you remove power for 5 minutes or 5 years.Īll programming is done entirely from the front of the keypad.

Iei 212w weatherproof keypad programming